Robe COLORSPOT 170 AT Specifications download pdf (Page 27)

the fixture On.Use the [ Up ] or [ Down ] buttons to select desired program ("tESt"- bilt-in program) or "OFF" if you

don't want trigger any program after switching the fixture On and press [ Enter ] to confirm or [ Mode ] to cancel

and return to the menu.Selected program will be played continuously in a loop as long as it appears on the display.

This option should be set "OFF" for all slaves in the master/slave chain by reason of the right program starts.

For example: You have selected program "PrG.3" in this menu and:

this fixture is set as a single fixture (master/slave or controller operating)- the fixture will run its program "PrG.3".

this fixture is set as a master in a data chain- the fixture will run its program "PrG.3".

this fixture is set as a slave in a data chain- the fixture will run its program according to the master(if the master

runs its own program "PrG.1", the slave will run its own program "PrG.1"also).

Note:If the fixture operates in the controller mode ( DMX controller is connected) and any program from this menu

is selected ,in this case the fixture will not respond to the DMX controller after switching On and will play selected

program.

- Playing program

This function allows you to run a bilt-in program "tESt" and the 3 freely-programmable programs

"PrG.1,PrG.2,PrG.3" .Press [ Up ] or [ Down ] buttons to select the desired program and press [ Enter ] to run

the program which will be played continuously in a loop.

If you want to pause the runnnig program in the required position, press the [ Enter ]-button(messages"PAU S "/"

program No."blink ).To continue the program running,press the [ Enter ]-button again.

Note:If the fixture operates in the controller mode ( DMX controller is connected) and any program from this

function is selected in this case the fixture will not respond to the DMX controller and will play selected program.

You can't play programs on the slave fixtures from their control panels if the master fixture is switched On and

connected to the slaves (playing is forced by the master).

- Editing program

This menu item allows you to select a program to edit or create.The COLORSPOT 170 AT has one built-in

program ("tESt") and the 3 free programs,each up to 99 steps.

If the fixture is set as a master ,then you may edit any program in the slaves.You can't edit programs on the slave

fixtures from their control panels if the master fixture is switched on and connected to the slaves (editing is

possible by the master control panel only).

Procedure:

1. Press [ Up ] or [ Down ]-button to select the program you want to edit ("PrG.1" - "PrG.3") and press [Enter ].

2. Press [ Up ] or [ Down ]-button to select the desired fixture ("MASt." - "SLA.9") and press [ Enter ]-button.

3. Press [ Up ] or [ Down ]-button to select the desired program step ("St.01" - "St.99") and press [ Enter ]-button.

4 Press [ Up ] or [ Down ]-button to select the desired item and press [ Enter ]-button.Now you can edit by [ Up

] or [ Down ] buttons the DMX value for selected item:

"P.End." - a total number of the program steps,value 1-99 .This value you must set before start

programming(e.g. if you want to create program with the 10 steps,set P.End.=10).

"PAn" - a pan,value 0-255

"tilt" - a tilt,value 0-255

"F.PAn" - a fine pan, value 0-255

"F.tilt" - a fine tilt,value 0-255

"SPEd" - a speed of PAN/TILT movement,value 0-255

"Colo." - a colour , value 0-255

"r.Gob." - a rot.gobo,value 0-255

"G.rot." - a G.rotation,value 0-255

"Foc." - a focus,value 0-255

"Stro." - a strobe, value 0-255

"dimr" - a dimmer, value 0-255

"S.tim." - a step time,value 0,1-25,5 seconds

"COPY." - a copying the current prog. step to the next prog. step .If the last prog.step is copied to the

next prog. step ,parameter "P.End" is increased about 1 automatically (except step 99).

5. Press [ Enter ]-button to confirm adjusted value .

6. Press [ Mode ]-button,select next prog. step and repeat this procedure (steps 4 and 6).

The editting programs "PrG.1,PrG.2,PrG.3" are saved in the current modified fixture (master or slave1-9).

Note:If you want to operate the programs in "Audio mode",set step time =0.25s or higher and speed=1 or higher

to ensure the fluent pan/tilt movement.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 36 37

Comments to this Manuals

No comments

Robe COLORSPOT 170 AT Specifications Page 27

Comments to this Manuals

Related products and manuals for Floodlights Robe COLORSPOT 170 AT